Hyundai Tucson: Driveshaft and axle / Special Service Tools
| Tool(Number and Name) | Illustration | Use |
| Ball joint remover 09568-1S100 |
| Removal of the tie rod end ball joint. |
| Lower arm ball joint remover 09568-4R100 |
| Removal of the lower arm ball joint. |
| Band installer 0K495-C5000 |
| Used for installing ear type boot band |
| Band installer 09495-39100 |
| Used for installing hook type boot band |
| Differential bearing remover 09501-C9200 |
| Used for removal of differential gear bearing |
| Differential assembly working stand base 09501-C9231 |
| Used for working on the differential carrier assembly (Use with 0K530-P2500, 0K501-P2232) |
| Rear differential assembly working stand adapter 0K530-P2500 |
| Used for working on the differential carrier assembly (Use with 09501-C9231, 0K501-P2232) |
| Sub support 0K501-P2232 |
| Used for working on the differential carrier assembly (Use with 09501-C9231, 0K530-P2500) |
| Bearing remover 09501-C9310 |
| Used for removal of the bearing (Use with 09452-2E000) |
| Bearing remover 09452-2E000 |
| Used as main body when removing the bearing (Use with 09501-C9310) |
| Bearing race remover (Main body) 09501-C9140 |
| Used for removal of the bearing race (Main body only) |
| Bearing race remover 09501-C9320 |
| Used for removal of the outside bearing race |
| Bearing race remover 09501-C9330 |
| Used for removal of the inside bearing race |
| Rear differential bearing installer 0K530-P2300 |
| Used for installing the differential gear bearing |
| Rear differential bearing installer 0K530-P2200 |
| Used for installing the pinion bearing race |
| Pinion bearing race installer 09501-C9340 |
| Removal & Installation of the differential assembly warking stand. |
| Pinion oil seal installer 0K530-P2100 |
| Used for installing the pinion oil seal (Use with 09231-H1100) |
| Differential oil seal installer 09501-C9190 |
| Used for installing differential case side oil seal (Use with 09231-H1100) |
| Handle 09231-H1100 |
| Using with 0K530-P2100, 09501-C9190 |
| Backlash measurement supporter 0K530-P2400 |
| Used to measure the backlash |
Specifications
- Specification
ItemsInner sideOuter side
Front driveshaftJoint type CWTJ#24 BJ#24
Max. permissible angle26°46.5°
Rear driveshaftJoint typeLTJ#20LBJ#20
Max. permissible angle20°
Rear differ ...
Front Axle Assembly. Front Hub / Knuckle / Tone Wheel
Front Hub / Knuckle / Tone Wheel
- Components
1. Front brake disc2. Front hub assembly3. Dust cover4. Front knuckle
- Removal
• When lifting a vehicle using a lift, ...
Other information:
Hyundai Tucson (NX4) 2022-2026 Service Manual: Rear Door Side Weatherstrip
- Replacement
[Rear door side weatherstrip]
1.Loosen the rear door checker (B) mounting bolt.Tightening torque :16.7 - 21.6 N.m (1.7 - 2.2 kgf.m, 12.3 - 15.9 lb-ft)
2.Detach the clips, then remove the rear door side weatherstrip (A).
3.To install, reverse removal procedure.
[Rear door bod ...
Hyundai Tucson (NX4) 2022-2026 Service Manual: Repair procedures
- Inspection
Front Door Lock Module Inspection
1.Remove the front door trim.(Refer to Body - "Front Door Trim")
2.Disconnect the connectors from the actuator.
3.Check actuator operation by connecting power and ground according to the table.PinDescription
DriverPanssenger
1-M2
2-M3
3COM- ...
