| Items | Inner side | Outer side | |
| Front driveshaft | Joint type | CWTJ#24 | BJ#24 |
| Max. permissible angle | 26° | 46.5° | |
| Rear driveshaft | Joint type | LTJ#20 | LBJ#20 |
| Max. permissible angle | 20° | ||
| Rear differential | Oil type | Hypoid gear oil API GL-5, SAE 75W/85 | |
| (SK HCT-5 gear oil 75W85 equivalent) | |||
| OIL capacity (L) | 0.58 ± 0.05 | ||
| Gear type | Hypoid | ||
| Diff ratio | 2.533 | ||
| Hypoid gear backlash | 0.07 - 0.15 mm (0.0028 - 0.0059 in.) | ||
| Diff gear backlash | 0.01 - 0.06 mm (0 - 0.0023 in.) | ||
| Items | N.m | kgf.m | lb-ft | |
| Front | Tire wheel hub nut | 107.9 - 125.5 | 11.0 - 13.0 | 79.6 - 94.0 |
| Driveshaft castle nut | 294.2 - 313.8 | 30.0 - 32.0 | 217.0 - 231.5 | |
| Strut assembly lower mounting bolt | 156.9 - 176.5 | 16.0 - 18.0 | 115.7 - 130.2 | |
| Brake caliper mounting bolt | 98.1 - 117.7 | 10.0 - 12.0 | 72.3 - 86.8 | |
| Wheel speed sensor mounting bolt | 6.9 - 10.8 | 0.7 - 1.1 | 5.1 - 8.0 | |
| Brake disc mounting screw | 4.9 - 5.9 | 0.5 - 0.6 | 3.6 - 4.3 | |
| Hub assembly mounting bolt | 78.5 - 98.1 | 8.0 - 10.0 | 57.9 - 72.3 | |
| Upper roll rod bracket bolt | (A) 107.9 - 125.5 | 11.0 - 13.0 | 79.6 - 94.0 | |
| (B) 49.0 - 63.7 | 5.0 - 6.5 | 36.2 - 47.0 | ||
| Lower arm ball joint mounting bolt | 98.1 - 117.7 | 10.0 - 12.0 | 72.3 - 86.8 | |
| Tie rod end ball joint mounting nut | 98.1 - 117.7 | 10.0 - 12.0 | 72.3 - 86.8 | |
| Rear | Tire wheel hub nut | 107.9 - 125.5 | 11.0 - 13.0 | 79.6 - 94.0 |
| Driveshaft castle nut | 294.2 - 313.8 | 30.0 - 32.0 | 217.0 - 231.5 | |
| Shock absorber lower mounting nut | 137.3 - 156.9 | 14.0 -16.0 | 101.3 - 115.7 | |
| Brake caliper mounting bolt | 78.5 - 98.1 | 8.0 - 10.0 | 57.9 - 72.3 | |
| Wheel speed sensor mounting bolt | 8.8 - 13.7 | 0.9 - 1.4 | 6.5 - 10.1 | |
| Brake disc mounting screw | 4.9 - 5.9 | 0.5 - 0.6 | 3.6 - 4.3 | |
| Hub assembly mounting bolt | 98.1 - 117.7 | 10.0 - 12.0 | 72.3 - 86.8 | |
| Upper arm mounting bolt | 137.2 - 156.9 | 14.0 - 16.0 | 101.2 - 115.7 | |
| Lower arm mounting bolt | 137.2 - 156.9 | 14.0 - 16.0 | 101.2 - 115.7 | |
| Assist arm ball joint mounting nut | 137.2 - 156.9 | 14.0 - 16.0 | 101.2 - 115.7 | |
| Trailing arm mounting bolt | 98.1 - 117.7 | 10.0 - 12.0 | 72.3 - 86.8 | |
| propeller shaft | Front propeller shaft mounting bolt | 49.0 - 68.6 | 5.0 - 7.0 | 36.2 - 50.6 |
| Propeller shaft center bearing bracket mounting bolt | 49.0 - 68.6 | 5.0 - 7.0 | 36.2 - 50.6 | |
| Rear propeller shaft mounting bolt | 49.0 - 68.6 | 5.0 - 7.0 | 36.2 - 50.6 | |
| Rear Differential | Rear differential mounting bolt | 78.5 - 88.3 | 8.0 - 9.0 | 57.9 - 65.1 |
| Differential cover mounting bolt | 39.2 - 49.0 | 4.0 - 5.0 | 28.9 - 36.2 | |
| Rear differential drain plug | 49.0 - 68.6 | 5.0 - 7.0 | 36.2 - 50.6 | |
| Rear differential filler plug | 39.2 - 58.8 | 4.0 - 6.0 | 28.9 - 43.4 | |
| Items | Lubricants | Quantity | |
| Front driveshaft | BJ 25 | RBA | 115 (+10/0)g |
| CWTJ 25 | CW-13TJ | 180 (+10/0)g | |
| Rear driveshaft | BJ 20 | RBA | 40 (+10/0)g |
| TJ 20 | CW-13TJ | 65 (+10/0)g | |
Special Service ToolsHyundai Tucson (NX4) 2022-2026 Service Manual: Electric Shift Button
- Removal
1.Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.Remove the console upper cover.(Refer to Body (Interior and Exterior) - "Floor Console Assembly")
3.Loosen the screw and then removing the electric shift button (A).
4.Loosen the screw and then removing t ...
Hyundai Tucson (NX4) 2022-2026 Service Manual: Rear Glass Defogger Printed Heater
- Inspection
Wrap tin foil around the end of the voltmeter test lead to prevent
damaging the heater line. Apply finger pressure on the tin foil, moving
the tin foil along the grid line to check for open circuits.
1.Turn on the defogger switch and use a voltmeter to mea ...